Message from @Dustin

Discord ID: 383865363055771649


2017-11-25 00:28:48 UTC  

Thanks means a lot coming from the reigning champ @joe TX

2017-11-25 00:43:20 UTC  

@Taylor TX There is an activism guide pinned in this channel you'll have to scroll up

2017-11-25 00:44:03 UTC  

Rutgers is a big job tho

2017-11-25 00:44:37 UTC  

We need to do umd one of these days @FlintShrubwood

2017-11-25 00:44:51 UTC  

Yea. Remember @Charlemagne MD We got a big response last time. Tim hit it I believe.

2017-11-25 01:49:49 UTC  

Great job @ashrob NJ

2017-11-25 01:50:23 UTC  

Thanks my man

2017-11-25 02:41:46 UTC  

Just bought a banner making setup.
A drop coming in the near future.
Im thinking of doing an Anti Com short slogan or "America Is Our Birth Right. "

2017-11-25 03:21:21 UTC  

@Taylor TX you can ask me about banners.

2017-11-25 03:29:52 UTC  

@Goodest_Boy average cost for a cheaper banner? Where do you buy your supplies (mainly the banner material and the method to secure and weigh it down)

2017-11-25 03:30:29 UTC  

PVC is cheaper, was scrolling in this thread and saw someone recommend master locks?

2017-11-25 03:45:23 UTC  

If you can jump in general chat in a couple minutes I can cover everything there.

2017-11-25 03:48:29 UTC  

@Goodest_Boy laying in bed with little one trying to settle him for bed. Give me a few and I might be able to hop in if nothing else than to listen to instructions with some headphones in.

2017-11-25 03:49:17 UTC  

You can pm me to if that works.

2017-11-25 03:51:23 UTC  

@Dustin @ashrob NJ Great looking work guys

2017-11-25 06:20:44 UTC  

https://cdn.discordapp.com/attachments/364051970409103362/383864568272650240/20171122_211823.jpg

2017-11-25 06:21:15 UTC  

These are what I'm issuing to weigh down my banners.

2017-11-25 06:21:53 UTC  

Usually found near the lumber section @ home depot.

2017-11-25 06:22:33 UTC  

Are you using Two plates and a bolt and nut?

2017-11-25 06:23:13 UTC  

Just 2 plates, 1 for each corner. Secured with a strong zip tie.

2017-11-25 06:23:54 UTC  

Maybe a little duct tape.

2017-11-25 06:25:11 UTC  

You can punch 4 holes in the cloth and use 4 zip ties on one plate

2017-11-25 06:25:33 UTC  

One moment...

2017-11-25 06:27:43 UTC  

I found these @ different sizes in a different hardware store - Orchard hardware. And they were cheaper in-store than the website says for some reason. Grommets already installed.

https://cdn.discordapp.com/attachments/364051970409103362/383866325153611787/Screenshot_20171124-222607.jpg

2017-11-25 06:28:30 UTC  

If it has grommets then your set.

2017-11-25 06:29:07 UTC  

Just make sure you have large enough zip ties or use multiple

2017-11-25 06:30:36 UTC  

I could only find large plastic ones, they work well. Very strong. I want to try metal zip ties - they might be harder to cut.

2017-11-25 06:31:45 UTC  

Make the entire banner out of sheet metal.

2017-11-25 06:31:53 UTC  

Weld the letters on

2017-11-25 06:32:26 UTC  

xD

2017-11-25 06:32:50 UTC  

Metal and cable is difficult to work with if you aren't used to it

2017-11-25 06:33:26 UTC  

Big brain Thomas always has the right answers

2017-11-25 06:34:02 UTC  

Make the banner bright green, so folks can see it better, maybe use some of that reflective paint, too. Might need to switch the lettering to white to make it pop out more. Add that onto the sheet metal and we should be good to go for a banner.

2017-11-25 06:34:53 UTC  

It'll def fit in your car

2017-11-25 06:35:11 UTC  

So make a racist road sign

2017-11-25 06:36:20 UTC  

It will fit in your TRUCK if you don't drive a supper duty then your a faggot

2017-11-25 06:36:35 UTC  

👌

2017-11-25 06:36:50 UTC  

Yfw not a Texan Master Race

2017-11-25 06:45:49 UTC  

https://cdn.discordapp.com/attachments/364051970409103362/383870878460542976/IMG_3362.JPG

2017-11-25 06:45:54 UTC  

https://cdn.discordapp.com/attachments/364051970409103362/383870898970558465/IMG_3364.JPG

2017-11-25 06:45:56 UTC  

https://cdn.discordapp.com/attachments/364051970409103362/383870907594178560/IMG_3365.JPG