Message from @Deleted User

Discord ID: 344970335529205770


2017-08-03 02:26:01 UTC  

I'm going to try and get my water pump inside and re fun all the pipeing

2017-08-03 02:26:06 UTC  

How hard should it be?

2017-08-03 05:06:54 UTC  

If you are talking about reconnecting the pump once it's inside the house it should not be too bad. They make a product called pecs which is a plastic water line with compression fittings. The requires a $100 tool to crimp them but when you're done you can take it back to Home Depot and return it for your money. If you're talking about rerunning pipe outside I would need a little more information. But anytime you can keep a water line deeper than 18 inches in the ground it won't freeze

2017-08-03 05:07:19 UTC  

*PEX

2017-08-03 05:10:56 UTC  

I am reconnecting it inside, thanks I'll have to look into it!

2017-08-03 05:11:38 UTC  

The plastic pipe has changeovers where you can connect to the existing copper it's very easy to run then color coded blue and red

2017-08-07 02:55:03 UTC  

I have an issue with a the doorway into my basement. First problem is that the bottom of the doorway is a quarter of an inch offset from the top. The second is there is not enough room on one side for the trim and I don't want to trim it to make it fit. Soooo I'm ripping it all out and doing it right. My question is how do I rough out the doorway to the appropriate size and ensure I have room on both sides for the trim? The door I have is 31 5/8" and with sheet rock up I only have a 37 " span. Once the trim is around the frame it's 36 1/2" so my rough out has almost no margin for error.

2017-08-07 03:13:29 UTC  

When you're roughing in for a door the rough opening is always about an inchor so bigger than your prehung door. That way you could shim on either side to true it up. If your casing is 31 and 5/8 inches if you put your rough opening approximately an inch greater and Center it in the opening to the basement you should be able to se t the prehung door and shim it to get it centered and true

2017-08-07 03:13:37 UTC  
2017-08-07 03:16:03 UTC  

I guess I should just spend the money foe a prehung door instead of trying to use the salvaged one I have.

2017-08-07 03:21:41 UTC  

I did not catch that sorry. Yes trying to frame in and hang a door is rough to do. Plus you have to go back and trim it all out. If you get a Ford a prehung door it would go a lot quicker and easier on you. Just try to find one that matches the opening so you don't have a lot of drywall patching

2017-08-07 03:22:01 UTC  

*can afford

2017-08-07 13:10:45 UTC  

@Placidseven - MO greg is totally right. I'll try to get to a door today if I can to show you how I do it.
Is your old door hollow? Or is it a slab or an old 5 panel?

2017-08-07 13:25:15 UTC  

@RevStench are you going to Charlottsville

2017-08-07 14:12:17 UTC  

@RevStench it's a 6 panel hollow core.

2017-08-07 16:40:07 UTC  

@Deleted User no sir, we're working every Saturday until who knows when. We picked up a few houses in Lexington.
@Placidseven - MO the advice Greg gave you is best, with that door. And I have to give you props for doing right and not doing some half assed hack job. Way to act your color hahaha

2017-08-09 20:43:17 UTC  

So I broke my favorite chisel on Monday and only had a Lowe's close by to go to and I picked up this thing. It's my new favorite toy.

I know @Jhawk nc wanted to go over sharpening knives and chisels, well Friday I'm going to spend the first part of my day sharpening all my hand tools(knife, chisel, and crosscut saw). I'll put together a little tutorial for you fellas, common sense stuff.

https://cdn.discordapp.com/attachments/322712446747934721/344943743868338176/20170808_100444.jpg

2017-08-09 22:26:24 UTC  

@Placidseven - MO#5546 I've hung probably over 100 salvage doors making my own jambs and milling my own trim etc. just make sure you have plenty of shims on hand. The long cedar work the best. It can get complicated especially if you mortis your hinges. Need a good router or laminate trimmer.
With a pre-hung most of the jambs are adjustable and the door is already hinged. Don't forget your level!

2017-08-09 22:27:57 UTC  

There's a ton of step by step vids on YouTube if you wanna go with the salvage. It is super rewarding after you get it done. I milled and hung all the doors and trim in my house

2017-08-09 22:28:16 UTC  

https://cdn.discordapp.com/attachments/322712446747934721/344970161939546122/image.jpg

2017-08-09 22:28:57 UTC  

https://cdn.discordapp.com/attachments/322712446747934721/344970334769774603/image.jpg

2017-08-09 22:36:36 UTC  

I love that trim. If I could afford it i'd remove all the trim from my house and do Victorian style trim.

2017-08-09 23:48:51 UTC  

https://cdn.discordapp.com/attachments/322712446747934721/344990442007298058/20170809_194849.jpg

2017-08-09 23:49:18 UTC  

This is my apartment, 1892

2017-08-09 23:52:28 UTC  

I do this type of work as well as windows a lot. Double hung weighted or taped and leaded glass.

2017-08-09 23:57:38 UTC  

https://cdn.discordapp.com/attachments/322712446747934721/344992653076856832/20150624_130131.jpg

2017-08-09 23:59:41 UTC  

This one had pictures of the inside so it had to go back original, early 1900s. Reclaimed wood from an old oak barn, and they painted it white...

2017-08-10 00:02:45 UTC  

@Deleted User I dig that look, but can I ask why everything is so square?

2017-08-10 00:07:53 UTC  

@RevStench what are those serrations on the side of that chisel what are those for

2017-08-10 00:53:17 UTC  

@Deleted User it's for cutting, like a knife. I cut a few cut nails with it today. Worked great. Holds an edge pretty well.

2017-08-10 01:03:11 UTC  

Damn. Mean chisel! Lowe's Kobalt tools are pretty good I've got a few of them

2017-08-10 01:32:47 UTC  

Yeah the few I have hold up pretty well. I can't recommend their lineman pliers, stick with Kline, which I'm sure you know better than I do.

2017-08-10 01:41:41 UTC  

Yeah blown up quite a few pairs

2017-08-10 02:07:58 UTC  

@RevStench#3208 nice trim! Square - basically what my wife wanted when she found all those doors.

2017-08-10 02:12:10 UTC  

That square hardware is Emtek, pretty good stuff we spent a mint on

2017-08-10 10:26:22 UTC  

@CJames - TN#6244 oh right on. Now you need one of these.

https://cdn.discordapp.com/attachments/322712446747934721/345150880280215554/20170216_131610.jpg

2017-08-10 13:35:38 UTC  

Haha

2017-08-10 14:20:35 UTC  

Hahaha that's awesome

2017-08-10 16:08:01 UTC  

This guy tells me he does stained glass, shows me this...

https://cdn.discordapp.com/attachments/322712446747934721/345236858814464002/20170718_114848.jpg

2017-08-10 16:10:10 UTC  

Little bullshit window decoration. He did sell it to this lady for $375.

2017-08-10 16:10:33 UTC  

So I showed him my leaded glass,

https://cdn.discordapp.com/attachments/322712446747934721/345237497724403714/20170808_133640.jpg