Message from @Festive
Discord ID: 649978458151190548
If you want to do a low shelf 80%, you just have to cut the pocket deeper in the rear right? Do the jigs and the specific 80% you buy have any effect on that?
I think youll have to do that bit freehand but it shouldnt be hard
Measure your depth and width and mark it then cut to the mark
You just use a longer router bit right? Or does the shelf get narrower once it gets lower?
I would suggest you buy a rifle to begin with before you worry about the other stuff
and then get gear
Found the answer to the rear lug pocket question here, step 6, if anyone else is curious. https://www.80lowerjig.com/blogs/80-lower-blog/how-to-complete-an-80-lower-router-or-drill-press-jig/
@Festive I think I get it. Once you cut the "high shelf" depth, you have to avoid the solid black areas when cutting to the "low shelf" depth, right?
@Misaki I might end up doing that, I'm really not sure yet. But I love the idea of making my rifle myself, to a reasonable extent.
@Red Korvo idk iv never done an 80% build
I might 3d print myself a lower to try that out too, and to have a physical model to help me understand what I'm doing better when I make a metal one.
Im just providin tips as i work with metal
Gotcha.
Appreciated.
If your really uncomfortable do a poly 80% build first its a ton easier
Metal can make your tools do some goofy shit if you arent ready
Make sure you punch any holes before drilling even with a drill press
Might do that too, but only if the jigs and tooling are the same. I don't want to buy two whole sets of tooling, that shit's expensive. I could try printing a 100% lower and an 80% lower, then practicing on the printed 80%.
The tools and steps will be the same
I will, especially if they're unsupported. But I think the jigs all have a lot of support for the bits.
But the plastic being softer itll be easier to do also you dont have to worry about your bits walking
The punch prevents the bit walk
Sounds good.
Also dont forget to step up the holes if its not wantin to cut
I've used punches for that before, and I'll do it if I have problems, but the jigs SHOULD do plenty to keep them from walking. They provide at least 1cm of steel around the hole to guide the bits.
Step up?
Start with a smaller bit and step up the size until its the correct size
Ah, so pilot holes, gotcha.
Yee
Niggas scared to use the cone bit but the thing works if you pay attention
So I've blocked you. Wondering why? Please consult the criteria below:
✔You're a <@&559943777024737292>
✔You're a <@&558119990725705748>
✔You're <@&559951530955112458>
✔You're an "<@&600465023772524565>"
✔You're a <@&559943292029239296>
✔You have <@&558103330405220383>
Discord is my weapon of justice, and the block button is my bullet. Pow (not supporting or advocating gun rights in any way. Just a metaphor)
<:cryingcat:404139925466906654>
I don't mind cone bits but these jig and tool kits should be pretty solid. I don't mind improvising if necessary but I shouldn't need to.
You wont know till youve got everything infront of ya
I'll probably get one of these, most likely the drill press jig because it's so cheap and I can borrow a drill press. https://www.80percentarms.com/ar-15-lower-jigs/
Oh absolutely. I'm just not too worried because the good kits have had the shit tested out of them so every step is well understood by the manufacturer.
Im thinkin about gettin a storage unit with power n making it my workshop
If anyone knows a good source for 80% lowers, especially if they're mil spec, let me know. Bonus points if they have an "auto" position marked in minecraft.
Good morning @PunishedSmug how was your thanksgiving
Gud
The blind leading the blind down here at <@&558119990725705748> general.