4/4 Remove gloves by pinching one cuff below the edge and pulling it down. The glove should be turning inside out as you pull it off. When the first glove is removed, hold it loosely in your gloved hand. With 2 fingers, pinch the cuff edge of the remaining glove and peel it down off of your hand, encapsulating the other glove as you go. When you’re done, you’ll have an inside out glove tweezed between 2 fingers with the other glove wadded up inside. Dispose of in a covered container. Wash your hands with Hibiclens or comparable soap, for at least 60 seconds. Finish by washing your face with an antimicrobial soap. Wound cleansers work well for this purpose. Other concerns: • Human waste could cause other illnesses to crop up; building an outhouse in the event of a pandemic would be a priority. • Depending on the rate of death by 2019-nCoV people that we know could die. This means that we would probably need to burn the bodies of infected as there may not be enough room for everyone and it is the most reliable way to prevent the spread of any disease from a dead body would be to incinerate the corpse. • Travel to and from settlements/towns should be limited to what is absolutely necessary as contact with large groups of people who could have 2019-nCoV drastically increases the risk of contracting the infection. Additionally, the chances that a town would have vital supplies will be low following the announcement of infection spread in a local area as people start to panic buy. • Starting a garden should be a primary priority as canned foods will only last so long. Lentils are a hardy staple and dry, store-bought, lentils can be planted. Other vegetable seeds in the cellar should also be used. • Protein will also be an issue; hunting can make up for this in the short-run however chickens, guineas, or cattle are more sustainable in the long run and pose fewer risks.

snares and traps for hunting

I like it

you mind giving me the prepper role too dubya

would 50% KNO3 work for black powder?

also I need the prepper role too

thank ye

same here yeeterino

can I use finely ground black powder or am I forced to use FFG (2F)?

would I need to use a stronger barrel for extraordinarily fine powder?

Depends on the amount of grams you put in

Doesn’t matter how fine the power is

Also consider the weight of the projectile you’re firing

And diameter of the barrel

this one website said that if the powder is too fine the pressure rises too quickly

there's a reason they use different grain sizes in modern rifles

look at the grain size used in 50bmg and 22lr

Idk much about black powder rifles, I’d just look at forums about it to get your best answer

this book says "for academic study only" so it should be ok

thanks to both of you

found this is another pdf

Commonly called “Four F”, this is the finest
granulation and is used for priming flintlocks.
Due to its rather limited use, it is usually
somewhat difficult to obtain. When necessary,
FFFG may be substituted. There is no
Pyrodex equivalent.
FFFG/Pyrodex “P”
Commonly called “Triple F”, this powder is
used in most single shot pistols and all
percussion revolvers. It is also popular for all
smaller caliber rifles up to and including 50
caliber. When FFFFG is not available, FFFG
may be used to prime a flint lock.
FFG/Pyrodex “RS” and “Select”
Commonly called “Double F”, this is a popular
powder for rifles over 50 caliber and up to 75
caliber. Also used in the larger caliber single
shot pistols and most shotguns.
FG
Commonly called “Single F”, this is the
coarsest granulation used for small arms. Use
is pretty much restricted to rifles over 75 caliber
and large bore shotguns. There is no
Pyrodex equivalent.

this pdf

I wanna make shotgun shells

thanks

>iamprepper

@Clitzkrieg

here

thankerino

https://www.primalsurvivor.net/homemade-shotgun-shells/ also this for anyone interested in the same thing

http://www.tbullock.com/bpsg.html

I also have 6 7.62x54R shells that I could reload but it would be hard to machine something for them with my tools

all I need now is a good 12 gauge tube

would mild steel work?

or do I need hardened stuff?

if i recall pressure on a 12 gauge is actually really low like at 12k psi so i would guess just black iron pipe would work

dont quote me on that tho

if unshure use whatever is safer

It all depends on how long you need it to work for

20 shots? Mild steel will work. More than that, you *will* get fucked

I personally hope not at all