Message from @Francis V

Discord ID: 471750453294792725


2018-07-11 23:58:43 UTC  

@Tanner - SC I get what you're saying and to be honest I'm not that worried about being displaced. I used to operate nuclear reactors and have an IQ in the 130 range. I farm because I love it. Not everyone is so lucky though.

2018-07-12 00:02:37 UTC  

Also I do only make $13 an hour farming. If I didn't have secondary sources of income farming would represent a pretty substantial reduction in my standard of living.

2018-07-12 00:02:57 UTC  

I understand and I'm not inconsiderate of our lower-IQ whites.

2018-07-12 00:03:41 UTC  

I just want to push back against the idea the disruption is bad. It's change, it's different, it's unknown, it might have short-term pain, but there is a lot of medium-term gain, including those lower IQ people.

2018-07-12 00:04:35 UTC  

Also, "If your IQ is 120 or higher, birth control should be illegal for you" - Richard Spencer

2018-07-12 00:05:12 UTC  

I love that quote and I keep in mind that it's a bit of our duty as high IQ guys to have high birth rates.

2018-07-12 00:19:10 UTC  

@Der Seeteufel - SD your lack of a decent wage has more to do with immigration than innovation

2018-07-22 19:42:25 UTC  

#JustNon-WhiteThings

2018-07-22 19:42:27 UTC  

https://cdn.discordapp.com/attachments/322712586741088256/470677026391588874/image.jpg

2018-07-24 17:45:01 UTC  

how...?

2018-07-24 18:21:09 UTC  

Cuz racism.

2018-07-24 21:41:22 UTC  

So I’m changing the compressor on a car today and every single piece of plastic a hose was attached to was brittle and broke. So a 1-2 hour job turned into waiting for JB weld to set overnight.

2018-07-24 22:08:54 UTC  

I'd almost say just replace all the hoses.

2018-07-25 16:09:54 UTC  

It’s the plastic fittings for the hoses!

2018-07-25 16:10:08 UTC  

They are all brittle from heat the hoses are fine

2018-07-25 16:10:37 UTC  

I replaced the fittings and jb welded them in place and it held up in a pressure test

2018-07-25 18:43:08 UTC  

https://cdn.discordapp.com/attachments/322712586741088256/471749261281984527/image.jpg

2018-07-25 18:43:12 UTC  

Fixing the school buses in my town

2018-07-25 18:43:20 UTC  

Brakes mostly tbh

2018-07-25 18:47:49 UTC  

https://cdn.discordapp.com/attachments/322712586741088256/471750439491207168/image.jpg

2018-07-25 18:47:52 UTC  

Also this old piece of junk

2018-07-25 18:48:09 UTC  

The new starter isn’t meeting the fly wheel any ideas why?

2018-07-25 18:48:22 UTC  

It’s got the right clearance but it won’t meet it

2018-07-25 19:03:19 UTC  

Access retainer makes this a 10 minute job

https://cdn.discordapp.com/attachments/322712586741088256/471754341271732265/image.jpg

2018-07-25 19:03:45 UTC  

Easy as 123

https://cdn.discordapp.com/attachments/322712586741088256/471754450361385010/image.jpg

2018-07-26 17:18:01 UTC  

The starter needed a bushing on the bolt holding it in because someone had milled out the bolt mount spot on the bell housing.

2018-07-26 17:18:44 UTC  

Which allowed the starter to sway about when it’s gear came in contact with the fly wheel

2018-07-27 14:27:08 UTC  

What are your opinions on rejetting carbs on a motorcycle after adding aftermarket exhaust? I've been told conflicting things from local shops and also rabbit holed into forums and found about a 50/50 split on opinions. I'm at about 5500ft elevation.

2018-07-27 14:27:59 UTC  

2005 Honda Shadow Aero 750

2018-07-27 17:16:14 UTC  

I always re jet mine when adding more freer flowing exhaust.

2018-08-06 00:49:40 UTC  

Wish me luck boys. I'm about to drive 250 miles in this old girl.

https://cdn.discordapp.com/attachments/322712586741088256/475827768832163848/20180805_191228.jpg

2018-08-06 00:54:30 UTC  

Don't worry mods it's registered to me and I'm actually excited to meet SD Antifa I'll by xer a beer.

2018-08-14 20:10:07 UTC  

Fuck changing these out lol

https://cdn.discordapp.com/attachments/322712586741088256/479018908788064257/image.jpg

2018-08-14 20:10:18 UTC  

You have no room to get your hands in there without taking the whole dash apart

2018-08-14 20:10:49 UTC  

It has about 5/6 if an inch of clearance from everything around it

2018-08-14 20:11:10 UTC  

I hate chevys

2018-08-15 02:15:14 UTC  

Eh I used to make a lot of money on dash/interior jobs.

2018-08-15 18:48:16 UTC  

It’s supposed to actuate the ac mode doors

2018-08-15 18:48:33 UTC  

However it will not self adjust the modes no matter what we try

2018-08-15 18:48:43 UTC  

It is supposed to do it automatically

2018-08-16 03:12:16 UTC  

If you are meaning you replaced the motor and it is still doing that sounds like you have a control module problem.