Message from Deleted User in MacGuyver - Skills & Academics #electrician


2017-07-25 05:20:05 UTC  

And even then, I'm not supposed to

2017-07-25 05:20:08 UTC  

But even then it can be difficult to trace underground work

2017-07-25 05:20:33 UTC  

Its funny that people freak about higher V

2017-07-25 05:20:48 UTC  

Voltage and current are inversely related

2017-07-25 05:21:02 UTC  

Meh. It all shocks the same. It's just not under our contractor's license.

2017-07-25 05:21:12 UTC  

I hear that

2017-07-25 05:21:59 UTC  

Do you fusion splice also?

2017-07-25 05:22:30 UTC  

Not personally, no.

2017-07-25 05:22:37 UTC  

I can terminate fiber though.

2017-07-25 05:22:58 UTC  

I feel like i wasted my time with fiber, certs but rarely get the work for it

2017-07-25 05:23:13 UTC  

Sc and st?

2017-07-25 05:24:02 UTC  

Yeah, fiber's exploding around here so it's actually pretty easy to find work as AT&T is pulling it to all the current businesses and ressies

2017-07-25 05:24:27 UTC  

And usually just SC

2017-07-25 05:24:54 UTC  

But I've done fiber patch panels that are in ST

2017-07-25 05:26:37 UTC  

When i was in the military i worked with a system that was fiber for engineering spaces on an aircraft carrier. Got out and barely touched glass

2017-07-25 05:27:18 UTC  

Ha. I didn't do any of this tech stuff in the service. I was combat arms

2017-07-25 05:27:44 UTC  

Nice

2017-07-25 05:27:52 UTC  

Got out and needed a job. Got picked up for an IT help desk and worked my way up from there. Eventually outsourced and got into low voltage from there.

2017-07-25 05:28:42 UTC  

Well anything you can learn that will let you eventually contract is good imho

2017-07-25 18:55:07 UTC  

Beginner question here: I'm currently working on rewiring the lighting in my basement; at present it's a mess of different fixtures, wiring, and breakers. My question is how many 100watt bulbs can I run off a 10amp breaker. Ideally I'd like 9 or 10 lights; should I upgrade to a 15amp, or will the 10amp handle that load?

2017-07-25 21:57:57 UTC  

@Izat - VA#3390 take the total wattage of the bulbs and / 120 volt that will give you the amperage of that circuit. you really want to keep the load on the breaker at 80% so with a 100 watt light bulb you're looking at 8 bulbs. It goes the same with CFL bulbs or LED bulbs. You take the total wattage and / your voltage to get your amperage

2017-07-25 21:58:53 UTC  

Your voltage in your residence should be 110 volt but for little pad you can use 120.

2017-07-25 22:00:21 UTC  

To go a little deeper if the wire is 14 gauge wire you can change that 10 amp breaker to a 15 amp breaker. If it is 12 gauge wire you can bump your breaker size to a 20 amp. A 10 amp breaker is not used these days. 15 20 30 at cetera are the applicable sizes according to code

2017-07-25 22:07:13 UTC  

I know the math does not work out exactly on that but that'll get you right in the ballpark

2017-07-25 22:09:11 UTC  

Awesome, so upgrading to a 15 amp breaker would be sufficient for 10 lights

2017-07-25 22:14:14 UTC  

Yes the wire needs to be at least 14 gauge before you can change the breaker safely. Once you have the 15 amp breaker in place as I said before simply count up the total wattage on your bulbs and / 120 and that will give you the amperage. on a 15 amp breaker you want to keep the amperage at 12 amps for your 80% rule

2017-07-25 22:16:01 UTC  

And 10 bulbs would give you about eight and a half amps so yes you would be fine on that

2017-07-25 22:16:34 UTC  

I'm pretty sure the wire is 12 gauge (not at the house rn), so I should be good

2017-07-25 22:16:48 UTC  

One more question - the basement's unfinished, so the joists are bare; is it code to drill holes thru each joist to run the line thru? I see a mix of that and stapling the wire to the underside of the joists. It would mean me drilling more holes, not enough space in the existing holes

2017-07-25 22:17:20 UTC  

If wire is number 12 you can put a 20 amp breaker in safely again keep it at the 80% rule which is 16 amps maximum load

2017-07-25 22:17:59 UTC  

(If you haven't picked up on it, I'm a complete novice; just bought my first house in April)

2017-07-25 22:18:27 UTC  

Gotcha

2017-07-25 22:18:37 UTC  

I'll go with 20 amps then

2017-07-25 22:18:44 UTC  

Code now tells us not to strap to the bottom of the floor joist. I guess that's in anticipation of finishing out an area further down the road. So if it were being inspected yes you would need to drill through the joist. The way you decide to do it is up to you it is an existing home with a mixture of both styles of wiring so it's kind of at a decision call on your part

2017-07-25 22:19:32 UTC  

Not sure that I'll end up finishing, but if its code it's worth the extra time to go ahead and do it

2017-07-25 22:19:39 UTC  

No problem that's what we're here for. You'll find a lot of this stuff is just common sense. You just need to exercise safety anytime you get into a live panel. If you're unsure of what you're doing you can always shut the main breaker off and use a flashlight or a headlight of some type to perform the work

2017-07-25 22:20:45 UTC  

^i did that twice already replacing all the outlets; I have a pretty healthy fear of getting zapped

2017-07-25 22:21:06 UTC  

Thanks again for your input, it's much appreciated 👌🏻

2017-07-25 22:21:54 UTC  

Yes I can be difficult because you have to kind of visualize how the circuit works a lot of times in order to work and safely. Anytime someone with limited experiences working on something they should be energized the circuit

2017-07-25 22:22:27 UTC  

* de-energize

2017-07-26 01:11:51 UTC  

I concur with greg 100%